neoVI RED 2
CAN FD, LIN, 1GB 이더넷(DoIP/XCP)용 차량 네트워크 인터페이스 및 데이터 로거
neoVI RED 2 Specification
Protocol Support
Networks / Inputs
Device Specifications
Timing Specifications
Network Specifications – CAN
Network Specifications – LIN / K Line / KW2K / ISO 9141 Up to 2x LIN (Local Interconnect Network)
- General Purpose IO: Pin 2 – MISC IO (0-40V) – can be configured as Analog/PWMIO
- General Purpose IO: Pin 1,3 and 4 – MISC IO (0-3.3V) – can be configured as Analog/PWMIO
- General purpose I/O rate report interval: 10 Hz to 1 kHz, or based on digital change
Protocol Support
- OBD
- J1939: Includes J1939 DBC, BAM, RTS/CTS
- UDS (ISO14229):
- Services include $19, $22, $23, $2A, $2C
- DBC, A2L (ASAP2 File), GDX, MDX, ODX support
- CCP: Includes A2L (ASAP2 file) and ROB support
- XCP: Includes A2L (ASAP2 file) and ROB support
Networks / Inputs
- 2, 4, or 8 x Dual wire CAN (all baud rates supported)
- 2 LIN / K Line / KW2K / ISO 9141
- 2 Gigabit Ethernet (1000BASE-T)
Device Specifications
- Low power consumption
- Comatose: 500 microamps
- Fast wake 70 milliamps
- Power supply: 5-60V operation
- LEDs: 10 programmable tri-color LEDs
- 2 LEDs for legacy status; 2 user buttons
- Temperature range: -40°C to +85°C
- On-board UPS power supply for safe shutdown of data logger
- Dimensions: 13.60cm by 11.22cm by 3.97cm
- LEDs (user programmable): 10 programmable tri-color LEDs
- SD card: 2 card slot support for up to 2 TB of storage; card
- formatted using FAT32 for PC compatibility
- DAQ Ethernet
- Vehicle connectors: 26-pin male HD D-sub
- One-year limited warranty
- Field-upgradeable flash firmware
- General purpose I/O: 4 MISC IO (0-40V); can be configured as analog/ PWMIO
- General purpose I/O rate report interval: 10 Hz to 1 kHz, or based on digital change
- USB host for RAD-IO2 or neoVI MIC2
- Standalone mode, including scripting, receive messages, transmit messages, expressions, I/O and transport layers
- J2534 and RP1210 A/B compatible for CAN / ISO15765- 2:2016 (CAN FD)
- Battery-backed real-time clock (RTC)
- Absolute orientation sensor combining accelerometer, gyroscope and magnetometer
- High precision GPS with external GPS antenna
- Buzzer
Timing Specifications
- 64-bit timestamping to an accuracy of 25 nanoseconds on all networks
- Simultaneous operation on all CAN/LIN networks
- Transmit message double-buffering on all networks, allowing back-to-back message transmission
Network Specifications – CAN
- 2, 4 or 8 x ISO CAN FD channels
- CAN 2.0B compatible for all CAN networks
- 2-8 dedicated ISO11898 Dual Wire CAN FD physical layers (TJA1043)
- Listen-only mode support
Network Specifications – LIN / K Line / KW2K / ISO 9141 Up to 2x LIN (Local Interconnect Network)
- Full support for LIN 1.X, 2.X and J2602
- LIN J2602 / 2.X compatible physical layer
- Software-enabled 1K LIN Master Resistor per channel
- LIN Bus Monitor Mode identifies errors: Sync Break Error State and Length, Sync Wave Error, Message ID parity, TFrameMax/ Slave Not Responding, Checksum Error and Transmit Bit Errors
- LIN Bus Master Mode operates at same time as LIN Bus Monitor
- LIN Bus Slave simulation, with or without an LDF file
- LIN Bus hardware schedule table with support for LIN diagnostics
- Initialization Waveforms, including Fast Init, Five Baud, and Custom
- Software-selectable baud rate