RAD Galaxy 2
차량용 이더넷 후분석을 위한 다채널 인터페이스
# 100/1000BASE-T1(차량용 이더넷) 16채널
# 10GBASE-T(일반 이더넷) 3채널# CAN (FD) 8채널 # LIN 2채널
- ✔ 100/1000BASE-T1 16채널을 지원하는 다채널 인터페이스 장비
- ✔ 최대 16개의 ECU 플래싱 지원
- ✔ 스크립트 기반 자동화 내구테스트 지원
- ✔ 이종 프로토콜간 게이트웨이 동작 가능
- · CAN ↔ ETH, ETH ↔ LIN 등
- ✔ 미디어 컨버터로 활용 가능 (100/1000BASE-T1 ↔ 10GBASE-T)
- · WireShark로도 이더넷 패킷 분석 가능
- ✔ 양방향 이더넷 패킷을 미러링할 수 있는 액티브 탭 모드 지원
- ✔ 오픈소스 API 제공(Python, C, C++, C# 등)
상세 사양
| 제품명 | RAD Galaxy 2 |
|---|---|
| 100/1000BASE-T1 | 16채널 지원 |
| 10GBASE-T | 3채널 지원 |
| CAN / CAN (FD) | 8채널 지원 |
| LIN | 2채널 지원 |
| 지원 프로토콜 | UDS/CCP/XCP/GMLAN/J1939/ISO15765-2 등 |
| 전원 공급 | 12V Barrel Jack or DB-26 Connector |
| 작동 전압 | 10V ~ 40V |
| 소비 전력 | 60W |
| 작동 온도 | -40°C ~ +80°C |
| PC 인터페이스 | RJ-45 Cable |
| 크기 | 약 17.9 x 21.6 x 4.7 cm |
| 무게 | 약 1.36kg (3 lb) |
| 보증 기간 | 1년 |
제품 개요
다채널 인터페이스 및 액티브 탭 장비입니다.
차량용 이더넷(100/1000BASE-T1) 16채널과 10기가비트 이더넷(10GBASE-T) 3채널을 지원하는 다채널 인터페이스입니다.이더넷으로 통신하는 두 개의 노드 사이에서 데이터를 모니터링하거나 변조하는 기능인 액티브 탭 기능도 지원합니다.
차량용 이더넷 미디어 컨버터로 활용 가능합니다.
· 10GBASE-T ↔ 100/1000BASE-T1와 같이 미디어 컨버터로 활용 가능합니다.
장비 LED만으로 통신 상태를 실시간 확인할 수 있습니다.
전면의 LED를 통해 CAN, LIN, 차량용 이더넷의 통신 상태를 확인할 수 있어 테스트 환경에서 유용하게 대응할 수 있습니다.
통신 속도 및 종단저항 설정이 간편합니다.
소프트웨어를 통해 차량용 이더넷의 Link Speed와 Duplex를 손쉽게 설정할 수 있으며,
CAN (FD) 통신의 BaudRate와 종단저항 설정도 클릭 한 두번으로 간단히 설정할 수 있습니다.
소프트웨어 연계 기능
Applications
· ECU level and system level automated testing· Automotive Ethernet Tap
· Parallel reflashing of up to 16x ECUs
· Automotive Ethernet to CAN FD
· SoAd/DoIP/ISO 15765 reflashing over Automotive Ethernet or CAN FD
Active Tap Configuration
One use of the RAD-Galaxy 2 is to act as an active tap with 8x 1000BASE-T1 taps, transparently tapping between devices.These can be any combination of 8 ECU-to-switch or ECU-to-ECU links. The traffic from each device on a tapped link is forwarded to its partner, ensuring seamless operation of the network.
Copies of all messages/streams are also aggregated and sent to the PC over the RAD-Galaxy’s 10G Ethernet link, where they can be analyzed using Vehicle Spy software.
Independent Ports Mode
The Rad-Galaxy 2 can be used to connect up to 16x 100/1000BASE-T devices to a computer.This is helpful for a number of use cases such as simulation, testing, diagnostics, and Parallel ECU flashing.
In addition, any of the Ethernet ports can be bridged internally allowing media conversion between BASE-T and BASE-T1 devices.
Central Gateway Testing
The RAD-Galaxy 2 is uniquely configured to test central gateways.Connect to the “clean” and “dirty” side of the central gateway with four Ethernet ports, as well as the 8x CAN FD networks.
All data is synchronized with better than 10 ns accuracy.
Automotive Ethernet PHY Testing
RAD-Galaxy 2’s user-friendly and powerful design allows you to validate and debug physical layer/PHY issues.The RAD-Galaxy 2 provides PHY-level information including signal quality measurement, master/slave or negotiation modes, and other status available from the PHY.
사용 예시
사용 매뉴얼 (영문)
브로셔 다운로드 (영문)