General Specifications
- 4th Generation neoVI Architecture: over 10x performance over previous devices
- Low Power consumption
- Power Supply: 4.5-40 Volt Power Operation
- LED Membrane Keypad : 10 Full Color LEDs indicate network status, 2 LEDs for legacy status; 2 user buttons
- Temperature Range: -40C to +85C
- On board UPS power supply for safe shutdown of data logger
- Vehicle Connectors : 26 Pin male HD D-SUB and 9 Pin Micro D-SUB
- Warranty: One Year Limited Warranty
- Firmware: Field upgradeable design (flash firmware)
- General Purpose IO: 2 MISC IO (0-40V) can be configured as Analog/PWMIO
- General Purpose IO rate report interval: 10 Hz to 1 Khz or based on digital change
- Microsoft Certified USB drivers
- USB Host for neoVI MIC GPS or Powering RAD-Moon accessories
- Isolated High Speed (480 MBPS) USB
- Stand-Alone Mode Including Scripting, Receive Messages, Transmit Messages, Expressions, IO, and Transport Layers
- J2534 and RP1210 A/B compatible for CAN/ISO15765, Keyword, and ISO9141
- microSD card slot support for up to 128 Gigabytes of storage (or up to the limit of newer SDHC cards). The removable card is formatted using FAT32 for direct usage in a PC.
- Battery backed real time clock (RTC)
Timing Specifications
- 64 Bit timestamping to accuracy of 10 microseconds on CAN and LIN networks and never overflows. 0.5 microsecond accuracy timestamp available if using one network only.
- Simultaneous operations on all CAN/LIN networks.
- Transmit message double-buffering on all networks allows back to back message transmission.
Network Specifications
8x CAN (6x CAN-FD and 2x CAN-FD / DWCAN / SWCAN / LSFT CAN)
4x LIN (Local Interconnect), ISO9141, Keyword 2000, or K and L Line
DoIP/XCP/Automotive Ethernet
- 8x CAN (FD) Channels (NON ISO CAN FD with free upgrade to dual ISO/NON ISO support in Q1 2016. Learn more about the CAN FD NON ISO to CAN FD ISO upgrade here.)
- 6 Dedicated ISO11898 Dual Wire CAN FD Physical Layer (MCP2561FD)
- 2 CAN with CAN MODE with 3 software selectable PHY options
- DW CAN MODE Dual wire : 2 Dedicated ISO11898 Dual Wire CAN FD Physical Layers (MCP2561FD)
- LSFT CAN MODE : 2 Low Speed Fault Tolerant CAN Physical Layers (TJA1055)
- SW CAN MODE: 2 Single Wire CAN Physical Layers GMW3089 / SAE J2411(MC33897)
- CAN FD Support on all dual wire channels
- Up to 1 M-Bit Software Selectable Baud Rate for arbitration phase (auto baud capable)
- Up to 8 M-Bit Software Selectable Baud Rate for data phase (auto baud capable)
- Listen only mode support
- Single Wire High Speed Mode, Test Tool Resistor, and High Voltage Wakeup support
- Two software programmable DW CAN termination circuits
- Super Bitsmash feature allows FPGA controlled CAN error and waveform generation
- Logic analysis mode to discover low level CAN errors
4x LIN (Local Interconnect), ISO9141, Keyword 2000, or K and L Line
- Full support for LIN 1.X, 2.X and J2602
- LIN J2602 / 2.X compatible physical layer
- Software enabled 1K LIN Master Resistor PER CHANNEL
- LIN Bus Monitor Mode identifies errors: Sync Break Error State and Length, Sync Wave Error, Message ID parity, TFrameMax/Slave Not Responding, Checksum Error and Transmit Bit Errors
- LIN Bus Master Mode operates at same time as LIN Bus Monitor
- LIN Bus Slave simulation - with or without an LDF file
- LIN Bus hardware schedule table with support for LIN diagnostics
- UART Based State Machine
- Programmable Timing Parameters including Inter-Byte, TX Inter-Frame, RX Inter-Frame and Initialization Waveforms (0.5 ms Resolution)
- Initialization Waveforms including Fast Init, Five Baud, and Custom • Software Selectable Baud Rate
- Logic analysis mode to discover low level LIN or K Line errors
DoIP/XCP/Automotive Ethernet
- 10/100 Ethernet PHY with low power mode
- Compatible with BroadR-Reach® with RAD-Moon Ethernet Converter Accessory
- Software controlled DoIP activation line