RAD-Gigastar
1000Base-T1 액티브 탭, 게이트웨이, 미디어 컨버터, 차량 인터페이스 & 데이터 로거
The RAD-Gigastar works as an active tap, media converter, vehicle interface, and Ethernet data logger.
The RAD-Gigastar can monitor one pair of 100/1000BASE-T1* connections with an additional pair of SFP cages to support optical/ copper SFP transceivers. In addition, the RAD-Gigastar can also operate as a programmable gateway to create an Ethernet-to-Ethernet or a CAN-Ethernet gateway.
The RAD-Gigastar makes any standard Ethernet device, laptop, or data logger compatible with 100/1000BASE-T1. In addition to its Automotive Ethernet capabilities, it offers 6x ISO CAN FD channels, 2x FlexRay channels, and standalone operation capability. Applications
|
- 2x 100/1000BASE-T1 using the Marvell 88Q2112 PHY
- 2x 100BASE-TX/1000BASE-T/1000BASE-X SFP ports
- 6x ISO CAN FD channels with selectable on-board termination
- 2x FlexRay receive channels with selectable on-board termination
- 1 LIN/K Line
- 1 DoIP activation line
- Flexible media conversion between 100/1000BASE-T1, 100BASE-TX, 1000BASE-T and 1000BASE-X1, and other PHYs via SFP2.
- Fully supports standalone mode, data logger mode, Wireshark and Vehicle Spy
- Logging to internal NVM at speeds up to 480Mbps (Optional NVM storage up to 512 GB)
- Intrepid Time Sync (ITS) provides hardware synchronization with other Intrepid tools and autonomous logger systems
- Isolated USB 3.1 connection or Gigabit Ethernet (1000BASE-T) for PC connection, depending on configuration
- 5.5-60V power range, compatible with in-vehicle power
- Push buttons to control modes, master/slave and speed settings
- Membrane LEDs to show link, error, and activity status
- Automatic power management wake up modes
- Intrepid Time Sync using Ethernet or CAN FD channel
Active Tap Configuration A primary use of the RAD-Gigastar is to act as an active tap, transparently interposing itself between a pair of Automotive Ethernet devices.This can be either an ECU-to-switch or an ECU-to-ECU link.The traffic from each device on a tapped link is forwarded to its partner, ensuring seamless operation of the network. Copies of all messages/streams are also aggregated and sent to the PC over the RAD-Gigastar’s Gigabit Ethernet link, where they can be analyzed using Vehicle Spy Enterprise software. |
Media Converter Mode The RAD-Gigastar can act as a media converter for 100/1000BASE-T1, 100BASE-TX, 1000BASE-T, 1000BASE-X to standard 10/100/1000 Ethernet which is useful for connecting a PC to a 100/1000BASE-T1 host or switch. This allows you to simulate nodes or perform direct diagnostics or ECU flashing. In addition, the “pure” media converter mode disables encapsulation of messages and allows connections between media of differing bit rates, buffering as needed. |
The RAD-Gigastar is capable of running real-time scripts and logging data to internal NVM at speeds up to 480 Mbps (Optional NVM storage up to 512 GB). With features like Real Time Clock (RTC) backup and supercap logging protection, RAD-Gigastar helps protect your data against unexpected power failure and crank events.
Intrepid Time Sync
RAD-Gigastar can be linked with other Intrepid tools and autonomous logger systems using the Intrepid Time Sync format. ITS uses a proprietary method to provide very tight microsecond timing sync to all connected devices. For example, by using ITS between a RAD-Mars and RAD-Gigastar, you can record a multigigabit data steams with up to 2 terabytes with the RAD-Mars, while recording even more data with the RAD-Gigastar. Both datasets will be fully synced.
Central Gateway Testing
The RAD-Gigastar is uniquely configured to test central gateways. Connect to the “clean” and “dirty” side of the central gateway with four Ethernet ports, as well as the 6x CAN FD networks. All data is synchronized with better than 10 ns accuracy
Automotive Ethernet PHY Testing
RAD-Gigastar’s user friendly and powerful design allows you to validate and debug physical layer/PHY issues. The RAD-Gigastar provides PHY-level information including signal quality measurement, master/slave or negotiation modes, and other qualities available from the PHY.
neoVI Comparison Chart
Product |
neoVI FIRE 3 |
neoVI FIRE 3 Flexray |
neoVI RED 2 |
RAD GIGASTAR |
Image |
|
|
|
|
Interface to PC |
Ethernet |
Ethernet |
Ethernet |
USB / Ethernet |
Ruggedized IP67 |
- |
- |
- |
- |
Ethernet Interfaces |
2x 1Gb 10/100/1000BASE-T, |
2x 1Gb 10/100/1000BASE-T, |
2x 1 Gb 10/100/1000BASE-T |
2x 100BASE-TX / 1000BASE-T / 1000BASE-X SFP, |
FlexRay (FlexRay VNET) |
- |
2 |
- |
2 |
CAN Dual Wire |
16 |
15 |
Up to 8 |
6 |
CAN FD Dual Wire |
16 |
15 |
Up to 8 |
6 |
Single Wire CAN |
2 |
2 |
- |
- |
DoIP |
2 |
2 |
2 |
1 |
LIN / K-Line |
8 |
4 |
2 |
1 |
Voltage Input |
5-60V |
5-60V |
5-60V |
5.5-60V |
IMU (accelerometer,gyroscope and magnetometer) |
Yes |
Yes |
Yes |
- |
WiFi |
Internal dual-band 802.11a/b/g/n WiFi |
Internal dual-band 802.11a/b/g/n WiFi |
Internal dual-band 802.11a/b/g/n WiFi |
- |
Wireless neoVI |
Yes |
Yes |
Yes |
- |
Modem |
External |
External |
External |
- |
GPS |
Built-in |
Built-in |
Built-in |
- |
HD video recording via |
Features Available in Future |
Features Available in Future |
Features Available in Future |
- |
Storage Type / Included Size (Largest Size) |
2x Full-size SD card slots. SD 3.0 compatible and supporting up
to 2 terabytes of total storage. Up to 800 Mbps logging performance. (1x 64
GB SD card included standard) |
2x Full-size SD card slots. SD 3.0 compatible and supporting up
to 2 terabytes of total storage. Up to 800 Mbps logging performance. (1x 64
GB SD card included standard) |
2x Full-size SD card slots. SD 3.0 compatible and supporting up
to 2 terabytes of total storage. Up to 800 Mbps logging performance. (1x 64
GB SD card included standard) |
64 GB, Optional storage up to
512 GB available upon request. |
- |