General Specifications
Timing Specifications
Network Specifications – CAN
Network Specifications – LIN
Network Specifications – DoIP / XCP / Automotive Ethernet
- Fourth-generation neoVI architecture: over 10x the performance of earlier devices
- Low power consumption
- Power Supply: 4.5-40V operation
- LED membrane keypad: 10 full-color LEDs indicate network status; 2 LEDs for legacy status; 2 user buttons
- Temperature Range: -40°C to +85°C
- On-board UPS power supply for safe shutdown of data logger
- Vehicle connectors: 26-pin male HD D-Sub and 9-pin micro D-Sub
- One-year limited warranty
- Field-upgradeable flash firmware
- General Purpose IO: 2 MISC IO (0-40V) – can be configured as Analog/PWMIO
- General purpose I/O rate report interval: 10 Hz to 1 kHz, or based on digital change
- Microsoft-certified USB drivers
- USB Host for neoVI MIC GPS or powering RAD-Moon accessory
- Isolated high speed (480 Mbits/sec) USB
- Standalone mode Including scripting, receive messages, transmit messages, expressions, I/O and transport layers
- J2534 and RP1210 A/B compatible for CAN/ISO15765-2:2016 (CAN FD)
- microSD card slot support for up to 128 GB of storage (or the limit of newer SDHC cards). The removable card is formatted using FAT32 for PC compatibility
- Battery backed real time clock (RTC)
Timing Specifications
- 64-bit timestamping to an accuracy of 25 nanoseconds on CAN FD networks and 10 microseconds on LIN networks with no overflow. Accuracy of 0.5 microseconds possible if using only one network
- Simultaneous operation on all CAN/LIN networks
- Transmit message double-buffering on all networks, allowing back-to-back message transmission
Network Specifications – CAN
- 8x ISO CAN FD Channels implemented using the industry standard Bosch MCAN CAN FD Core
- CAN 2.0B compatible for all CAN Networks
- Software selectable between ISO CAN FD and NON ISO CAN FD (BOSCH CAN FD)
- 6 Dedicated ISO11898 Dual Wire CAN FD Physical Layer (MCP2561FD)
- 2 CAN with CAN mode and 3 software-selectable PHY options
- DW CAN mode: 2 dedicated ISO 11898 Dual Wire CAN FD physical layers (MCP2561FD)
- LSFT CAN mode: 2 Low Speed Fault Tolerant CAN physical layers (TJA1055)
- SW CAN mode: 2 Single Wire CAN physical layers GMW3089 / SAE J2411(MC33897)
- Up to 1 Mb/s software-selectable baud rate for arbitration phase (auto baud capable)
- Up to 8 Mb/s software-selectable baud rate for data phase (auto baud capable)
- Listen-only mode support
- Single Wire High Speed Mode, Test Tool Resistor, and High Voltage Wakeup support
- Four software programmable DW CAN termination circuits
Network Specifications – LIN
- 4x LIN (Local Interconnect)
- Full support for LIN 1.X, 2.X and J2602
- LIN J2602 / 2.X compatible physical layer
- Software enabled 1K LIN Master Resistor per channel
- LIN Bus Monitor Mode identifies errors: Sync Break Error State and Length, Sync Wave Error, Message ID parity, TFrameMax/Slave Not Responding, Checksum Error and Transmit Bit Errors
- LIN Bus Master Mode operates at same time as LIN Bus Monitor
- LIN Bus Slave simulation – with or without an LDF file
- LIN Bus hardware schedule table with support for LIN diagnostics
- Software-selectable baud rate
Network Specifications – DoIP / XCP / Automotive Ethernet
- 10/100 Ethernet PHY with low power mode
- Compatible with 100BASE-T1/BroadR-Reach® with RAD-Moon Ethernet Converter Accessory
- Software controlled DoIP activation line